Produktai skirti duja (455)

Offers excellent performance for multigas measurements in dry sampling, including HCl, HF, NO, NO2, N2O, SO2, CO, CH4, TOC, CO2 and O2. MultiGas NDIRGFC analyzer (NonDispersive Infrared Gas Filter Correlation) measuring up to ten gases simultaneously, including Nitrogen Oxide (NO), Nitrogen Dioxide (NO2), Sulphur Dioxide (SO2), Carbon Monoxide (CO), even Hydrogen Chloride (HCl) and Hydrogen Fluoride (HF). • process optimization and environmental compliance • measurement of dry and corrosive samples • fast and simultaneous measurements of up to 10 gases • dry basis measurement • automatic cross interference correction

Probenaufbereitungssystem zur Entnahme von Probengas aus einer unter Druck stehenden Erdgasquelle. Partikelfilter:1 micron Edelstahl T-Filter Maximaler Probengasdruck (Einlass):ca. 200 bar Druck am Ausgang:0.0 – 1.0 bar (typischerweise 0.28 bar)

Ideal zur Überwachung von Hg-Reduzierungssystemen an verschiedenen Messstellen. Messkomponente:Gesamtquecksilber UV-Quelle:Elektrodenlose Hg-Niederdrucklampe (EDL) Stabilisierung:Referenzstrahl-Technik Optische Zelle:Quarzglas Messbereich:0,05 μg/m³ bis 500 μg/m³ Hg Nachweisgrenze:0,0001 μg/m³ (Detektor); < 0,01 μg/m³ (System)

Messung von ionischem und gebundenem Quecksilber in Rauchgas. Thermokatalytische Behandlung des Rauchgas direkt am Kamin. Messkomponente:Gesamtquecksilber (TGM) UV-Quelle:Elektrodenlose Hg-Niederdrucklampe (EDL) Stabilisierung:Referenzstrahl-Technik Optische Zelle:Quarzglas Messbereiche:0 – 50 µg/m³; 0 – 75 µg/m³; 0 – 500 µg/m³ Nachweisgrenze:< 1 µg/m³

The dry extractive SEC™ system dries the gas sample at the sampling point, eliminating the necessity of an expensive heated sampling line.

Automatisch Null-, Präzisions-, Messbereichs- und Mehrpunktkalibrierungen mit NO, NO2, SO2, CO, O3, Kohlenwasserstoffen und anderen Gasen. US-EPA Zulassung:Ja

Approved flue gas velocity CEM for stack velocity, volumetric flow and pollutant mass release calculations when linked to gas and dust CEMS. Measured parameters:Flue-gas velocity Technology:FlueSonic™ Ultrasonic Measurement/Monitoring capability:0 – 50 m/s Stack/Duct diameter suitability:up to 10 m Flue gas temperature:up to 200 °C Baghouse:Yes Cartridge Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber:Yes QA checks:Yes

US EPA PS11 capable ProScatter™ particulate CEM for the extractive sampling and measurement of particulate in saturated wet gas streams. Measured parameters:Dust Technology:Extractive ProScatter™ Forward Scatter Measurement/Monitoring capability:0-500 mg/m³ Stack/Duct diameter suitability:up to 15m Flue gas temperature:up to 200°C Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber:Yes QA checks:Yes

Standard Reference CLD method for low & ultra low NOx measurement, IRGFC for CO, CO2, SO2, N2O, NOx, HF, HCl, TOC and O2 in a single analyse. Fast and simultaneous measurements of up to 10 gases. • measurement of dry and corrosive samples • unheated sample line • intrinsic security with onboard residual H2O measurements • onboard oxygen measure for environmental reporting • highly accurate, excellent stability with automatic optical stability check

The MGC101 system automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases.

Continuous particulate monitoring for saturated wet stack applications typically found after wet scrubbers, wet electrostatic precipitators and wet flue gas desulphurisation plants. Measured parameters:Dust Technology:Extractive ProScatter™ Forward Scatter Measurement/Monitoring capability:0-500 mg/m³ Stack/Duct diameter suitability:up to 15m Flue gas temperature:up to 200°C Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber :Yes

Flue gas flowmeter for continuous measurement of gas velocity, temperature and pressure in exhaust gas ducts (chimneys or flue pipes). Measured parameters:Flue-gas velocity Technology:Micro-venturi Measurement/Monitoring capability:3 – 30 m/s Stack/Duct diameter suitability:300 mm up to 1,5 m Flue gas temperature: up to 400 °C Baghouse:Yes Cartridge Filter:Yes Ceramic Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes Wet Electrostatic Precipitator (WESP):Yes

Ecodesigned, ultracompact, smart & connected instrument, the MIR 9000e is your next tool to measure combustion exhaust gas from boiler or gas from different industrial furnaces and process applications. It offers superior metrological performances for the simultaneous multigas measurement of NOx, SO2, CO, O2, residual H2O, CO2, CH4 and N2O (greenhouse gases). • ultralow power consumption • no compressed air required • insensitive to T° variations in the range +5 °C to +40 °C • proactive, userfriendly remote communication • highly accurate, excellent stability, economical, easy and reduced maintenance

Perfect ammonia gas analyzer or multigas analyzer for the measurement in hot & wet fluegas of HCl, HF, NH3, NO, NO2, N2O, SO2, CO, CO2, O2 and H2O. Heated MultiGas NDIRGFC analyzer for emission compliance and analysis of wet sample gases in corrosive applications, including DeNOx (SCR / SNCR) and for the optimization of flue gas treatment processes. • temperature maintained at 180 °C • measurement of raw and purified flue gas for desulfurization • measurement of wet and corrosive samples • no nitrogen required for calibration • QAL1 certified analyzer • remote access for all analyzer functions • low maintenance and low consumables requirement

Approved flue gas velocity CEM for stack velocity, volumetric flow and pollutant mass release calculations when linked to gas and dust CEMS. Measured parameters:Flue-gas velocity Technology:ProPitot™ Averaging Pitot Measurement/Monitoring capability:3 – 50 m/s Stack/Duct diameter suitability:up to 8 m Flue gas temperature:up to 800 °C Baghouse:Yes Cartridge Filter:Yes Ceramic Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes Wet Electrostatic Precipitator (WESP):Yes

This device is ideal for mercury determination at varying sites. Measuring principle:Thermocatalytic reduction at stack, amalgamation (MI GoldTrap), cold vapor atomic absorption (CVAAS) Measured component:Total mercury UV-Source:Electrodeless low pressure mercury lamp (EDL) Measuring ranges:0,05 μg/m³ to 500 μg/m³ Hg Detection limit:0,0001 μg/m³ (Detector); < 0,01 μg/m³ (System)

Der LAS 5000XD verwendet die durchstimmbare Diodenlaserspektroskopie (TDLS) und ist in verschiedenen Modellvarianten für die Messung von Parametern wie NH3 + H2 O, HF, CO + CO2 , O2 , HCl + H2O, usw. erhältlich. Der robuste Analysator mit schneller Reaktionszeit (1 s) und hochgenauer Messung, wurde für raue Umgebungen entwickelt. NH3 + H2O:0–10 ppm / 0–5000 ppm + 0–5% / 0–40% HF:0–3 ppm / 0–500 ppm CO + H2O:0–50 ppm / 0–1% + 0–5% / 0–40% CO + CO2:0-1% / 0-100% + 0-1% / 0-100% Untere Nachweisgrenze:< 1% des FS Reaktionszeit (0-90%) – Kurz:1 s

Überprüfung und Kalibrierung von Hg-Messgeräten. Konzentrationsbereich:ca. 10 bis 500 µg / m³ Hg° Volumenstrom Kalibriergas:1 bis 9 l/min, je nach eingestellter Konzentration Trägergas:Luft, Stickstoff Trägergasfluss:max. 12.5 l / (Min)

LAS 5000XD uses Tunable Diode Laser Spectroscopy (TDLS) and comes in various models for measuring parameters such as NH3 + H2O, HF, CO + CO2, O2, HCl + H2O, etc. It combines robustness, fast response time (1 s) and high accuracy measurement in harsh environments. NH3 + H2O:0–10 ppm / 0–5000 ppm + 0–5% / 0–40% HF:0–3 ppm / 0–500 ppm CO + H2O:0–50 ppm / 0–1% + 0–5% / 0–40% CO + CO2:0-1% / 0-100% + 0-1% / 0-100% Lower Detection Limit:< 1% of FS Response Time (0–90%) – Short:1 s Lack of fit/Linearity :≤ ±1%

MVS 2M is a multichannel system allowing to distribute two, three or four channels of fluids and signals to a gas monitoring system (GMS). Operating temperature:+5°C to +40°C Communication port:RS232/RS422, Ethernet

Null-Luft-Generator gibt kontinuierlich bis zu 20 Standardliter pro Minute (SLPM) trockene, schadstofffreie Luft ab. Standardliter pro Minute (SLPM):20 Interner Kompressor:Ja Innentrockner:Typ PSA

Rack 3U monitor using the TDL extractive technology to measure online the NH3 pre and/or post catalyst: SCR (Selective Catalytic Reduction) or SNCR (Selective Non-Catalytic Reduction) Gas:NH3 Principle of detection:Tunable Diode Laser Spectrometry (TDLS) Ranges:0-100 / 0-20 ppm Precision 2σ :1.8 ppm @ 1 s; 0.8 ppm @ 10 s Response time:< 2 sec (T90) (at gas flow rate of 3 L/min) Cell temperature range:190°C Operating temperature:+15 to +50°C Communication:RS 232 Dimensions:Rack 19″ – 3U

Gas chromatography (GC) coupled with a PID detector. VOC monitor QAL1 certified to EN 14662-3, the newest standard for benzene measurement. Measured parameter:VOC (Benzene, Toluene, Ethylbenzene, m+p-Xylene, o-Xylene, 1,3 Butadiene) Technology:Gas Chromatography US-EPA Approval / QAL 1 Certification:Yes Measurement ranges:up to 1000 µg/m3 Measurement units:ppb, ppm, µg/m3 (user-selectable) Noise (σ):≤ 0.025 µg/m3 at 0.5 µg/m3 benzene Lower Detectable Limit (2σ):≤ 0.05% µg/m3 benzene Zero drift:≤ 4% / 15 days Span drift:< 1% / 7 days

UV Fluorescence gas monitor offering excellent performances for the monitoring of SO2 in the range 0-10 ppm or 0-1 ppm. Option: H2S / TRS monitoring. Measured parameter :SO2 Technology:UV Fluorescence US-EPA Approval / QAL 1 Certification:Yes Measurement ranges :0-1 ppm or 0-10 ppm user-defined Measurement units:ppb, ppm, µg/m3 user-defined Lower Detectable Limit (2σ):< 0.4 ppb Noise (σ):< 0.2 ppb Zero drift:< 1 ppb / 24h Span drift:< 0.5% / 7 days Linearity:± 1%

Der MIR 9000P gehört zur neuen Generation der ENVEA Gasmessgeräte, die sich durch ECO-Design und smarte Technologie auszeichnet. Er misst gleichzeitig 8 Gase – NOx, SO2, CO, CO2, CH4, N2O, O2 und Rest-H2O – und verwendet die nicht-dispersive Infrarotmethode (NDIR-GFC) mit Gasfilterkorrelation. O2 wird durch einen eingebauten paramagnetischen SRM-Sensor gemessen. Der Analysator wurde entwickelt, um die speziellen Anforderungen von Messungen vor Ort zu erfüllen und bietet eine hervorragende Mobilität, Robustheit, Genauigkeit und Konformität. All dies macht ihn zu einem einzigartigen Gasemissionsmessgerät mit hoher Produktivität und niedrigen Betriebskosten. US EPA konform:Ja Probenahme:Kalt / Trocken -Extriebe Probenahmetransfer:Nicht beheiztes Polytube / beheizte Probenahmeleitung Eingebaute O2 Option:Ja Messbarer Parameter:SO2, NO oder NOx, CO, CO2 , N2O, CH4, O2 und Rest-H2O Programmeinheiten:ppm, mg / m 3 oder% Vol.

QAL1-zertifizierter Gasanalysator zur Überwachung von SO2 im Messbereich 0-10 ppm oder 0-1 ppm. Messgröße:SO2 Technologie:UV Fluoreszenz QAL 1-Zertifizierung:Ja US-EPA Zulassung:Ja Messbereiche:0-1 ppm oder 0-10 ppm benutzerdefiniert Messeinheiten:ppb, ppm, µg/m3 benutzerdefiniert Untere Nachweisgrenze (2σ):< 0.4 ppb Rauschen (σ):< 0.2 ppb

Gas monitor for fast, precise, direct and continuous measurement of NO2 concentrations in the range 0-1000 ppb. Measured parameter:NO₂ Technology:CAPS (Cavity Attenuated Phase Shift Spectroscopy) US-EPA Approval / QAL 1 Certification:Yes Measurement ranges :0-1 ppm Measurement units:ppb, ppm, µg/m3 (user-selectable) Lower Detectable Limit (2σ):0.1 ppb Noise (σ):0.05 ppb Zero drift:0.75 ppb/24h Span drift:1.5 ppb/12h Linearity:< 4%

Beheizter Multi-Gas NDIR-GFC-Analysator zur Emissionsüberwachung in korrosiven Anwendungsbereichen, auch für DeNOx (SCR / SNCR) und zur Optimierung von Rauchgasbehandlungsprozessen. Heiß/Nass-Extraktiv für die gleichzeitige Messung von: HCl, HF, NH3, NO, NO2, N2O, SO2, CO, CO2, O2 und H2O. QAL1 zertifiziert, nach EN 15267-3:Ja US EPA Konform:Ja Probenaufbereitung:Heiß/Nass Extraktiv Entnahmeleitung:Entnahmeleitung beheizt 180°C Kalibriergas:Ja, an Entnahmeeinheit oder Analysator Built-In O2 Option:Ja Serielle Schnittstelle:RS232 / RS422

Gaschromatographie in Verbindung mit einem Photoionisationsdetektor zur Messung von organischen Verbindungen wie Benzol, Toluol, Ethylbenzol, m+p-Xylol, o-Xylol, 1-3 Butadien. Messbare Parameter:VOC (Benzene, Toluene, Ethylbenzene, m+p-Xylene, o-Xylene, 1,3 Butadiene) Technologie:Gaschromatographie QAL1-Zertifikat:Ja US-EPA Zulassung:Ja Messbereich:0-1000 µg/m3 Messeinheit:ppb, ppm, µg/m3 (frei wählbar) Nachweisgrenze (2σ):≤ 0.025% µg/m3 at 0.5 µg/m3 benzene Rauschen (σ):≤ 0.5%

CLD based gas monitor offering superior performances for the measurement of NO, NO2 and NOx criteria pollutants in the range 0-1 ppm or 0-10 ppm. Optional NH3 monitoring. Measured parameter:NO, NO₂ & NOx (NH3 optional) Technology:Chemiluminescence US-EPA Approval / QAL 1 Certification:Yes Measurement ranges:0-1 or 0-10 ppm Measurement units:ppb, ppm, µg/m3 (user-selectable) Lower Detectable Limit (2σ):< 0.2 ppb Noise (σ):0.1 ppb Zero drift:< 1 ppb / 24h Span drift:< 1% / 7 days Linearity:1%