Produktai skirti vartojo (10)

Le casse contatore personalizzate in ottone sono progettate per offrire soluzioni affidabili e durature per la misurazione di vari flussi in diversi settori. Realizzate con ottone di alta qualità, queste casse contatore offrono una resistenza eccezionale alla corrosione e una lunga durata, rendendole ideali per applicazioni domestiche e industriali. La possibilità di personalizzare queste casse secondo le specifiche del cliente garantisce un adattamento perfetto e un funzionamento ottimale, migliorando l'efficienza e la sicurezza dei sistemi in cui vengono utilizzate. Le casse contatore in ottone sono utilizzate per misurare flussi di acqua, gas, alta pressione, flussi elettronici, liquidi industriali, calore e fluidi visciosi e corrosivi. Grazie alla loro robustezza e versatilità, rappresentano una soluzione affidabile per qualsiasi progetto che richieda componenti di alta qualità e prestazioni durature. Investire in casse contatore personalizzate in ottone significa scegliere qualità, affidabilità e innovazione per le proprie applicazioni di misurazione.

ART. 3372 CERNIERE PER NAUTICA IN ACCIAIO INOSSIDABILE 304 PERNO FISSO Confezione: 24pz Dimensioni (mm): 40x55x1,5

Sealgum Hydro-expanding waterstop sealant with a special mix of natural and synthetic rubbers and hydrophilic agents: in contact with water, it increases up to triple its volume compared to the original size (if used in environments with the presence of sea water the expansion will take place anyway but slightly reduced in volume). Sealgum is a simple waterstop easy to use, not requiring particular preparation on the supports, pre-shaped compartments, etc.. Sealgum waterstops are available in different sections: Sealgum 20.05 = 20x5 mm; Sealgum 20.10 = 20x10 mm; Sealgum 20.20 = 20x20 mm; Sealgum 50.05 = 50x5 mm; Sealgum 100.05 = 100x5 mm. Creation of castings and connections with safe and permanent hydraulic hold. Take care to create the laying site of the waterstop as smooth and even as possible. Remove any flaking, inconsistent, dusty, etc. parts. Sealgum must be spread on the laying surface and fastened using nails (steel nails plus water approx. every 25 cm). Sealing of the joints is ensured by simple placement side by side and not overlapping the ends. Positioning must guarantee good coverage of 10-12 cm by the concrete, to contain the expansive action generated by hydration. For particularly disconnected or rough surfaces, you can position Sealgum with the help of a hydro-expanding sealant in a cartridge Flexseal 300. 1.1 m/m: Use 1 metre of Sealgum for each linear metre, being careful to place 5-10 cm of the product alongside the end/start roll points to guarantee the permanent water tightness of the system. Sealgum 20.05 Roll 10 m - Sealgum 20.10 Roll 10 m - Sealgum 20.20 Roll 5 m - Box: 5 x (Sealgum 20.05 Roll 10 m) - Box: 7 x (Sealgum 20.10 Roll 10 m) - Box: 7 x (Sealgum 20.20 Roll 5 m)

Stesura manuali d'uso e manutenzione e traduzioni in varie lingue con valutazione dei rischi generazione di technical file per certificazione CE e stesura delle specifiche tecniche in varie lingue

Il profumo microincapsulato al lampone è una scelta eccellente per chi ama le fragranze dolci e fruttate. Questo profumo cattura l'essenza succosa e vibrante dei lamponi, offrendo un aroma che è al contempo fresco e accattivante. Grazie alla tecnologia di microincapsulazione, il profumo viene rilasciato gradualmente, garantendo una lunga durata e un'esperienza olfattiva costante. Ideale per profumare ambienti domestici o spazi commerciali, il profumo al lampone aggiunge un tocco di freschezza e vivacità.

ART. 3370 CERNIERE PER NAUTICA IN ACCIAIO INOSSIDABILE 304 PERNO FISSO Confezione: 24pz Dimensioni (mm): 40x42x1,5

ART. 3370 CERNIERE PER NAUTICA IN ACCIAIO INOSSIDABILE 304 PERNO FISSO Confezione: 24pz Dimensioni (mm): 40x70x1,5

Sanavel Breathable, natural, non-toxic, indoor paint, based on potassium silicate. Mineral-based, active formulation, high mildewcide and anti-condensation performance, prepared according to traditional recipes, for use in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanavel consists of potassium silicate, natural pigments. It has very high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances and toxic emissions in general, and does not have thermoplastic effects. Restoring and decorative paint for interior environments. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc. Pre-existing paints (washable, organic, solvent based etc. ) must be thoroughly removed. Preliminarily treat the support with the fixative Sanaxil Fix. Apply by brush, roller or spray. Sanavel is "dust-free" (it has started to be consistent to the touch) after about 1 hour. It can be overcoated after 4-5 hours, while it will be dry in-depth after 10-12 hours. Apply from 0.30 to 0.40 liters of Sanavel per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanadek Breathable, natural, non-toxic paint, for internal use, diffusive type, based on long hardening lime putty, prefiltered. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanadek has high breathability, it has remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and interior renovation paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. Apply from 0.30 to 0.40 liters of Sanadek per square metre of surface to be painted. Pail 4 l - Pail 14 l

Protech WAC-RC Single-component colored finish in water dispersion for the opaque protection of concrete surfaces and cementitious substrates, wall coverings, and appropriately prepared and primed floors. The product is a painting system suitable for environments with the presence of food, which can be used to protect walls and ceilings that comply with the HACCP protocol, in order to prevent possible food contamination. Excellent resistance to atmospheric agents and aggressive industrial environments Good water vapor permeability and water repellency Wide range of colors available Uniform matte finish Low maintenance over time Good resistance to diluted acids and alkalis, fuels and hydrocarbons Excellent resistance to detergents and disinfectants Excellent resistance to mold attack Perfectly washable It meets the following requirements: Legislative Decree n. 193 of 06/11/2007 “Implementation of Directive 2004/41/EC relating to food safety controls and application of community regulations in the same sector” - HACCP UNI 11021:2002 “Products and systems for painting environments with the presence of food”, in particular it is suitable for walls, ceilings and surfaces for which resistance to washing is required; can be washed with chloroactive detergent (detergent A); can be washed with alkaline degreaser (detergent B); can be washed with acid descaler (detergent C); can be washed with disinfectant (detergent D); resists temperature changes. Colored protective finish of concrete surfaces, cement plasters Anti-carbonation finishing of concrete structures Wall finishing for food, wine and butcher shops Wall finishing for chemical and pharmaceutical industries Finishing and coating of suitably prepared metal surfaces Protective finish for floors already treated with resins or primed Protective treatment of oxidized asphalt surfaces Finish for environments in the presence of food. Concrete The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, traces of coatings and surface treatments, etc. Any weak or detaching parts must be removed before applying the product by mechanical sanding with diamond discs and dust extraction. The tensile strength must not be less than 1.5 N/mm². The application of Protech WAC-RC on new or particularly absorbent cementitious substrates must always be preceded by the application of a coat of Protech fix AC water-based anchoring primer. Wait 3-4 hours before applying the finish. Resin coatings The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, etc. Sand the surface by mechanical sanding with diamond discs and dust extraction. It is advisable to wash the surfaces and wait for them to dry completely before applying the finish. The application of Protech WAC-RC on resinous and multilayer systems must always be preceded by sanding the entire surface in order to promote and guarantee optimal adhesion of the product to the support. PVC Wash the PVC surfaces to be treated with specific detergents to remove any substances that may affect the adhesion of the coating such as dirt, grease, oil, materials that block the pores in order to promote better capillary penetration of the product into the support. The application of Protech WAC-RC on PVC supports can be carried out directly with appropriate dilutions of the product in first and second coat. Steel Any welding residues must be removed and the joints sanded. Sandblast to cleanliness level Sa 2½ according to ISO8501-1. The surfaces to be coated must be free from dirt, oil, grease and impurities. Average surface roughness degree RZ ≥ 50 μm. An anti-corrosion treatment is recommended before applying the coating. The application of Protech WAC-RC on steel supports must always be preceded by the application of a coat of “surface tolerant” epoxy-polyamide primer in the solvent phase Syntech Poliurea Primer Epoxy Metal. Approximately 0.20 kg of Protech WAC-RC for each square meter of surface to be painted for each coat. Apply two coats.. Packaging: 20 kg bucket UM: €/kg