Produktai skirti prekės grąžinimo sąlygos (7)

Liquid product based on lithium silicates, which was created for the protective, consolidating and porosity reducer treatment of concrete, mineral, brick and stone substrates. It guarantees optimal durability and adhesion strength, resistance to UV rays, chemical agents and mechanical stresses. The result of the application allows to obtain a rapid hardening of the surface as well as a revived and homogeneous appearance of the same. The product has a negligible environmental impact thanks to the low VOC content (<50 g / l) and is practically odorless. Protective, reinforcing, water repellent treatments of concrete, mineral and stone supports. Specific product for revitalizing, simultaneously providing a great consolidation and an annulment of the dust produced in concrete supports, interstices, brick, stone or mixed arches, present in taverns, public premises and of historic monuments interest. The application surfaces should be clean, free of incrustations, dust etc. A preliminary wash with distilled water or steam it's recommended. The support should be dry when applying. Apply the product as it is, with low pressure sprayer or brush with long bristles. Keep the substrate wet with Consilex Idrofix for at least 20 minutes during application. If applied on floors, wait 24 hours before passing on the treated support. The reinforcing contribution will be completed after 2-3 weeks of treatment. From 0,20 to 1,00 kg of Consilex Idrofix per square meter of surface to be treated, based on the porosity of the support.

Protech WAC white Anti-carbonation, protective, decorative paint, pigmented for whitewashing concrete surfaces; based on acrylic resins in aqueous emulsion, it forms a film that is impermeable to water, with very low permeability to carbon dioxide but high vapour permeability, anchored by specific adherence and diffusion. Perfect for protective coatings of infrastructure projects in concrete. Painting of protective, decorative and anti-carbonation finish, for walls, façades, concrete products, plaster, masonry, natural stones, porous supports in general. Specific for painting industrial works and infrastructure artefacts: bridges, viaducts, large prefabricated, etc. The surfaces of application should be clean, free of any soiling, crumbling and non-adhering parts, or non-absorbent, dust, pre-existing paints, etc. Degraded or uneven surfaces should be reclaimed with products of the family REPAR or with adhesive cement mortars packaged in situ, based on Bond HG and polypropylene fibres Readymesh PM-180. Despite it is a good habit to apply an acrylic paint after preliminary treatment of the surfaces with the suitable reinforcing fixative Protech Fix AC, in the case of Protech WAC this operation is not strictly necessary. Apply the product in 2 coats, with a brush, roller or spray, diluting it with water according to the following dosages (% in weight): - roller or brush = 10% - spray = 15%-25% Apply from 0.25 to 0.35 kg of Protech WAC per square metre of surface to be painted. Packaging: 22 kg bucket Unit of Measure: €/kg

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Estrusori Per Cartucce Professional metal extruder guns for products in cartridges of various sizes. They are robust, ergonomic, easy to use and light extruder guns, to guarantee applications in the most disparate fields of traditional and specialized construction. Available for cartridges of various sizes, both for single cartridges and for double bimix cartridges of 300cc, 400cc, 470cc, 530cc, 600cc. Extrusion of materials in single cartridge or double bimix cartridge. Product to buy as needed. Extruder gun for 400 cc cartridges 1 unit - Extruder gun for 470 cc bimix cartridges 1 unit - Extruder gun for 600 cc bimix cartridges 1 unit - Extruder gun for 533 or 600 cc cartridges 1 unit - Extruder gun for 300 cc cartridges 1 unit

A non-film chemical/mechanical nano-technological hardener with a base of lithium silicates for cortical consolidation, chemical surface hardening and anti-dust treatment of recently-constructed industrial concrete flooring. QL Nano Lithium must be applied on the surface of the floor, immediately after finishing with mechanical bladed trowels. Once the product has been absorbed, it is possible to polish the treated surface using specific polishing machines. It is the most significant progress in the saturation and the reinforcement of concrete floorings in the last 50 years, it has always been used in the United States. The "nanotechnology" of QL Nano Lithium, which is a real improvement with respect to sodium silicate and extremely performant as a reinforcing agent for concrete, has allowed us to achieve levels of performance that were previously unimaginable. The product also presents the following characteristics: -It significantly limits (90%) the cracks of the flooring during hardening. - This is the only chemical hardener that helps to alleviate and prevent the alkali-silica reaction ( "alkali-aggregate reaction" or ASR). - It completely replaces the armour with quartz dusting. It does not crack, it does not detach, it creates a film, it does not bubble. - The extraordinary contribution to the deep reinforcement, makes the surface of the concrete completely dust-proof and highly resistant to abrasion. The continuous use of the flooring contributes to continuously improving the surface gloss without altering slipperiness in the least. - It is in an aqueous solution and does not contain solvents. It is odourless, non-flammable, non-toxic, it does not fear the freezing and thawing cycles, it is not carcinogenic and does not contain volatile substances (VOC Free) and can also be used in closed premises. - Compatible with other materials like: epoxy resins, polyurethane resins, acrylic resins, etc.. - It is UV resistant and remains stable over time. Anti-dust hardening treatment, for industrial flooring and concrete slabs, both old and new, both grey and coloured. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". In case of new flooring, it can be applied as soon as the surface of the industrial flooring is walkable, without superficial water residue. Shake the product before use. Apply the product by low pressure airless, evenly without creating puddles, completely saturating the surface for a consumption of 70 g/m² approximately. It is advisable, after about 7-10 days, to wash the surface floor polisher provided with a black pad to eliminate any excess product, thus obtaining an elegant semi gloss (opaque) effect of the flooring, by polishing the lithium crystals on the surface. Approximately 0,07 litres of QL Nano Lithium for every square metre of surface to be treated.

An anti-dust chemical/mechanical revitalising hardener for concrete flooring and screeds, consisting of an aqueous solution of mineral silicates and fluosilicates, activated by specific wetting agents. It is applied in several coats of decreasing dilution in water, with a brush or mechanical “scrubber”. Specific anti-dust treatments for industrial flooring or concrete slabs that have lost their original “vitality”. It reacts with the calcium compounds, soluble and unstable, present in of concrete products, transforming them into new stable, insoluble and resistant compounds. Consequent increases in resistance to wear and tear of the order of 200% -400%, significant increases in chemical stability, resistance to freeze-thaw cycles etc. Reactive impregnations for stabilising chemical and mechanical structures and concrete products. Hardening, anti-dust, anti abrasive and anti-corrosion treatments for concrete floorings. Adjustment of the chemical and mechanical performance of products for the industrial, rural and livestock construction (on horizontal surfaces). Apply, preferably with a brush or with "washer dryer" machine on the basis of the following indications: - Porous surfaces: repeated applications of a solution of water and QL Fluosil at a ratio in 1:1 - Compact surfaces: apply three coats, with decreasing dilution with water. 1a coat 1:3, 2a coat 1:2, 3a coat 1:1. The consumption of QL Fluosil will be proportional to the absorption of the floor to be treated. Indicatively a porous surface will consume about 400 g/m², while a surface with normal porosity will consume 250-300 g/m². Leave the product to dry between one coat and the next and then, after the last coat, wash with copious amounts of water. Protect glass and aluminium surfaces during application. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface".

Osmocem Flex Mono Osmotic cementitious waterproofing from a single-component, fibre-reinforced modified polymer, being super adhesive and deformable, with a plastic-elastic conduct. Ideal for waterproofing beneath tiles and for protecting concrete. It is easily applied by trowel, brush or roller, both on horizontal and vertical surfaces. Offers a 30% higher yield than two-component systems. One-component product, modified polymer, flexible and deformable, which requires only the addition of water. The application is easy and versatile, thanks to the variable consistency obtained by adjusting the amount of water added (within the allowed range and indicated in the "Instructions for use" paragraph), without dripping in vertical applications. 30% higher yield than two-component systems. Waterproofing of balconies, terraces, bathrooms, showers, swimming pools, before laying ceramic coverings. Waterproofing of concrete structures, plasters and cementitious screeds, as long as they are sufficiently porous and absorbent and without waterproofing and / or water-repellent surface treatments, both chemical (siloxane, epoxy, polyurethane, etc.) and natural (waxing). The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, water-repellent treatments in general, etc. Any cracks due to plastic or hygrometric shrinkage, if present, must be preliminarily reclaimed with suitable products and techniques. In micro-cracked or particularly stressed areas, it is important to insert Armaglass 160, an alkali-resistant fiberglass mesh, in the first fresh layer of Osmocem Flex Mono. Immediately after laying the mesh, Osmocem Flex Mono must be finished with a flat trowel (see also "Instructions for use"). In the case of large cladding surfaces, it is necessary to provide "chimneys" for venting the steam, suitably located. Osmocem Flex Mono must be mixed with clean water. The following water additions are allowed: • 22-24% for application with a trowel. • Maximum 30% for brush-roller application. It is recommended to mix with a low speed mixer for at least a couple of minutes and, in any case, until a perfectly homogeneous and lump-free mixture is obtained. The addition of other ingredients (binders, aggregates, additives) must be absolutely avoided. A light wetting of the support is allowed immediately before the product is spread. Dry substrates must be previously primed with Bond Plus (mixed with water in a ratio of 1: 1). The typical application involves an application of about 3 mm of Osmocem Flex Mono in two layers. The maximum recommended thickness for each applied layer is: by trowel / spray: 2 mm, by roller / brush: 1 mm. When waterproofing terraces and balconies, Osmocem Flex Mono must be applied in two successive coats, with a thickness of approximately 1.5 mm each (approximately 2.2 kg / m² per coat), each of which must be applied when the previous one appears stable. (not earlier than 4 hours at 20 ° C). It is recommended to interpose the Armaglass 160 alkaline-resistant glass fiber mesh in the thickness of Osmocem Flex Mono between the first and second coat. The Proband butyl self-adhesive strip must also be prepared between the screed and the elevation walls. Finally, it is recommended to position the special elastic band Elastotex 120, or Elastotex 120 Cloth, in correspondence with any expansion joints, fixing it with the same Osmocem Flex Mono. Do not use Osmocem Flex Mono on heavily degraded or inconsistent substrates, as they would risk nullifying the goodness of the waterproofing. Do not apply on slightly or non-porous substrates or substrates previously coated with water-repellent treatments in general, unless after appropriate roughening using bush hammering machines, sanders and equipment suitable for preparatory treatments of the substrates, or after appropriate treatment with suitable polymeric primers. Approximately 1.4 kg / m² of Osmocem Flex Mono for each millimeter of thickness to be created. Packaging: 20 kg bag UM: €/kg