Produktai skirti 5140 skystas molis (4)

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Das erste Resin speziell für den 3D-Druck von Verschleißteilen und Zahnrädern. Für feinste Details (Präzision: ± 0,1 mm, kleine Zahnräder ab Modul m = 0,2) und enorme Lebensdauer durch integrierte Festschmierstoffe und die hohe Biegefestigkeit (90 MPa). Das 3D-Druck Kunstharz iglidur i3000 ist zur Verarbeitung auf DLP- und LCD-Druckern geeignet und wurde speziell für den Druck von Zahnrädern und Verschleißteilen entwickelt. Mit einer mindestens 30-mal bis 60-mal höheren Lebensdauer als herkömmliche 3D-Druck-Harze eignet sich iglidur® i3000 für jegliche Arten der Verschleißanwendung. Durch die hohe Auflösung von bis zu 35 μm können sehr filigrane Bauteile mit feinsten Details gedruckt werden. Die mechanischen Eigenschaften sind durch das Photopolymerisationsverfahren weitestgehend isotrop. Wenn Sie selbst über keinen DLP- oder LCD-Drucker verfügen, bieten wir auch die Fertigung von Bauteilen aus Resin in unserem hauseigenen 3D-Druck-Service an. Kontaktieren Sie uns gerne. Nettogewicht:1000 g Farbe:grau

TECHNICAL DEFINITION CE 78 PERFECT’LISS is a ready-to-use lightweight compound specially formulated for finishing interior substrates (walls and ceilings). COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservative and various admixtures. The compound is white. SUITABLE SURFACES Plasterboard, plaster, AAC, brick, fibreglass cloth, gypsum block, concrete, render, old paint. APPLICATION Roller, trowel or airless applications of the product are possible. For roller application, the product should be mixed before use. Nozzles recommended for airless application : 35 and 41. AMOUNT REQUIRED Depends on the thickness applied : from 0.4 to 2 kg/m². DRYING TIME The second coat can be applied 6-24 hours after the first, depending on the ambient conditions.

INCI : Kaolin Origine : Maroc UGS:AR-5 Contenant:100g, 250g